s8n 13 Posted October 25, 2014 hi members and Swizzy , im currently on 16537 and thinking of updating the dash to 16747 via USB will i be able to RGH the console ? i believe i can but want to be sure btw my Coolrunner 4's have been shipped and should arrive Monday Quote Share this post Link to post Share on other sites
Anonymous 95 Posted October 25, 2014 So you have planned for modding your Console Is this your first time for modding??? Do you knw what kind of mother board u hav??? Did u read proper tutorials?? Sent from my ST23i using Tapatalk Quote Share this post Link to post Share on other sites
s8n 13 Posted October 25, 2014 hi Anonymous , ive been researching and planning for about 6 months now it is my first time modding a 360. The motherboard is a Jasper , i have read 2 different Tutorials and watched Youtube videos from Keil423 and thedopesoner930 ive also asked questions over at TX forums and here. ive written my own guide/tutorial after researching for my own use , i will use it when the Coolrunners arrive i want to get Swizzy to check the guide/tutorial i wrote at some point Quote Share this post Link to post Share on other sites
Swizzy 2085 Posted October 25, 2014 ive written my own guide/tutorial after researching for my own use , i will use it when the Coolrunners arrive i want to get Swizzy to check the guide/tutorial i wrote at some point Where is it at? Jaspers can be hacked with any kernel version now a days, the stability of the hack depends on what version of CB you're on (if you can use JTAG it's always going to be stable, rgh 1 is fairly easy to get stable) if you're on a unsupported CB for these hacks, you should probably go for R-JTAG (or CR4) as it's fairly easy to get stable aswell 1 Quote Share this post Link to post Share on other sites
s8n 13 Posted October 25, 2014 hi Swizzy great tips as usual , below is my guide/tutorial a very small portion is copied and pasted from the Coolrunner manual. 1. solder QSB's to XBOX motherboard , after that plug in power and power on the 360. if it boots fine the soldering is good and theres no bridges or other problems etc............. 2. turn off and disconnect power from 360 , then connect J-Runner IMPORTANT plug in power but dont turn the 360 on fire up J-Runner software , do 4 Reads of the NAND make sure NAND Type is set for the motherboard make sure theres no errors in the log................... after 4 Reads done compare NANDs so they match........... compare 1 and 2then 3 and 4then 1 and 3 if they all match zip up the NAND files , they will most likey be in the ' output ' folderFLASHCONFIG - MOTHERBOARD TYPE01198010 - Xenon, Zephyr, Opus, Falcon00023010 - Jasper 16mb, Trinity 16mb008A3020 - Jasper 256mb00AA3020 - Jasper 512mb if motherboard is not 00023010 - Jasper 16mb, Trinity 16mb , contact Swizzy 3. now write the ECC , make sure there are no errors in the log once written wait 30 seconds then disconnect power and wait 30 more seconds. remove J-Runner cables from QSB's............... now solder wires from the Coolrunner 4 to the QSB's and motherboard. 4. try and boot XELL , plug in power and network cable turn on 360 from the front of the console once XELL has fully loaded get the IP address of the 360 and enter it into J-Runner software. hit ' Get CPU Key ' J-Runner should show KV info when it retrieves the CPU Key 5. J-Runner should reload your nanddump1.bin into source box again in preparation of key validation and image creationif it doesnt automatically reload it ' browse ' and manually load nanddump1.bin into the source boxNow you should have all the info in KV tab in the right hand box and you will get a CPU Key verified message in the logtake a snapshot of the screen with Hypersnap of ............ NAND infoKV infoBad BlocksAt this point you now have all the info you need to create a Freeboot image.Turn off XBOX and disconnect power , wait 30 seconds 6. Reconnect J-Runner Programmer and connect power but dont turn on the XBOX in J-Runner software goto Dashlaunch tab and enable ' use Dashlaunch 'enable ' include launch.ini 'use the configurator to my liking in J-Runner create launch.ini save the settingsNow click Create XeBuild Image button make sure theres no errors in the log 7. Now flash this image to your NAND press Write NAND make sure theres no errors................... Once finished flashing wait 30 secondsunplug power and wait for 30 more secondsremove J-Runner Programmerthen plug in USB hard drive with FreeStyleDash on itThen replug power to 360 and turn on Quote Share this post Link to post Share on other sites