vick79
-
Content Count
35 -
Joined
-
Last visited
-
Days Won
2
Everything posted by vick79
-
I wasn't using my brain, evidently. I will have to check that and get back to you.
-
I've tried switching phat and slim, but I don't know about a jumper next to the switch. Unless you are talking about JP. I have not removed it. I have never used a rev c before, but I installed a rev D in a Jasper 512 and I had to remove the resistors on the Crystal and cap. I had to bridge 2 and 3, and J and P. That system instantly boots every time. Other than the Crystal clock, what are the differences in the rev c and rev d? I have only used rev d and ACE chips before now.
-
It boots original nand with post connected, does this mean I'm not getting a good connection to post?
-
Stock nand works fine, I think it's the speed up I'm hearing.
-
I know this doesn't help you, but how long can you run stealth before getting banned?
-
When I get home from work, I am going to resolder everything. I looked over my soldering after a comment earlier, and I think Stevie Wonder could do a better job. I will never solder over someone elses house while somebody is over my shoulder, asking multiple questions, after being up for 56 hours, again. Unfortunately, there is nothing wrong with my camera, it looks that bad. I will post my results after resoldering it. My Xbox didn't deserve this. I have re-soldered, shortening my wires in the process. Same results. Someone in another forum suggested enabling cap, same results. If I disable my CR chip, I can hear the CPU resetting at the same rate. I don't know if this helps, but if I program CR with RGH 2 timing file,the green led never lights up. I'm not sure, but I think I might have a bad glitch chip.
-
Thank you. Sorry about everything, but this is the first time I ever posted in a forum. The last pic 0020 is of my CLK point. I used the alternate point.
-
Unfortunately my camera on my phone sucks. I have re-soldered it so many times, trying to fix the issue, yes the soldering is starting to look like crap. I added to much solder to my PLL point. Since I'm not doing this for anybody else, I can redo it later. Just want to get it working. I think my POST wire is bad, I'm getting terrible continuity through it. I will replace the wire and post results.
-
I can't get them to post. Here are the links to them. https://mega.nz/#!j5sVDBxA!TR6hHb6tqf-shnFS8vh0V2F9QAEC-SvuwdPkGsZ8kp4 https://mega.nz/#!HoFkBSjJ!2U3LTRezvh6zu8rrrDcZVEalCPwCGYcRjidT-8c1iy0 https://mega.nz/#!2oFCzY5a!RPSNaAwVKR2juF7fXpf98tOgixIMGfyeEmDA77wfXsw https://mega.nz/#!Wp0BGQpJ!VGvv99EEqu54tmDZYMFSHarIk-CDXqPJOntJKnzjJMY https://mega.nz/#!egtlUaTC!oF3pU4iaIxTChaRLqnXq17z9iRBNI9XNXMXq7rx-A5Y
-
I have searched the internet to no avail. I hope somebody can help me here. I have done my fare share of RGH 1.2, and RGH 2, but never had this issue. My Coolrunner keeps glitching at the same rate no matter what timing file I put in it. I can't get xell to boot. I tried pulling the wires one at a time, if I remove RST, PLL, or POST it quits trying to glitch. The CLK doesn't seem to make a difference. If I re-write my original nand, it boots fine so hardware is still good. I forgot to mention, I'm doing RGH 1.2 on a Jasper 256mb. If anyone could help me it would be greatly appreciated.