Issues with Xell not loading after CR$ install

[MrKronic 7]

Hello again. So this time, I've been having an issue with another phat Jasper console that has been installed with a CR4 XL board. The NAND has been flashed with Xell, but so far I've had no luck in actually booting into it. The console starts up normally (no RRODs whatsoever and the power light turns green etc.), but I don't get any display regardless of which display port I use (I've tried the composite and the HDMI).

So far, I've done a POST monitor of the boot-up which seems to indicates that everything seem to be initializing properly and no POST faults, however the code cascade seems to be a bit too long in comparison to the normal POST codes (including the expected Xell code) in Martin C's POST calculator. Also, strangely enough, after the console is switched on the first time, the POST monitor always initializes with a 7F code and stays stuck in it regardless of whether the xbox is switched on or not. This is reset every time I switch off the power box and repeat the process.

===================================================
Monday, July 13, 2015 1:55:18 AM

J-Runner v0.3 Beta (7) Started


WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button


Checking Files
Finished Checking Files
Checking Console..
Version: 10
Flash Config: 0x00000000
Can not Continue
Can not continue
Checking Console..
Version: 10
Flash Config: 0x00AA3020
00AA3020
Jasper 512MB
CB Version: 6723
Version: 10
Press Escape to exit
Waiting for POST to change
Post 01
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 0E
Post 0F
Post 10 - Payload/1BL started
Post 11 - FSB_CONFIG_PHY_CONTROL
Post 12 - FSB_CONFIG_RX_STATE
Post 13 - FSB_CONFIG_TX_STATE
Post 14 - FSB_CONFIG_TX_CREDITS
Post 15 - FETCH_OFFSET
Post 16 - FETCH_HEADER
Post 17 - VERIFY_HEADER
Post 18 - FETCH_CONTENTS
Post 19 - HMACSHA_COMPUTE
Post 1A - RC4_INITIALIZE
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 1F
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post 22 - INIT_SECENG
Post 23 - INIT_SYSRAM
Post 24 - VERIFY_OFFSET_3BL_CC
Post 25 - LOCATE_3BL_CC
Post 26 - FETCH_HEADER_3BL_CC
Post 27 - VERIFY_HEADER_3BL_CC
Post 28 - FETCH_CONTENTS_3BL_CC
Post 29 - HMACSHA_COMPUTE_3BL_CC
Post 2A - RC4_INITIALIZE_3BL_CC
Post 2B - RC4_DECRYPT_3BL_CC
Post 2C - SHA_COMPUTE_3BL_CC
Post 2D - SIG_VERIFY_3BL_CC
Post 2E - HWINIT
Post 2F - RELOCATE
Post 30 - VERIFY_OFFSET_4BL_CD
Post 31 - FETCH_HEADER_4BL_CD
Post 32 - VERIFY_HEADER_4BL_CD
Post 33 - FETCH_CONTENTS_4BL_CD
Post 34 - HMACSHA_COMPUTE_4BL_CD
Post 35 - RC4_INITIALIZE_4BL_CD
Post 36 - RC4_DECRYPT_4BL_CD
Post 37 - SHA_COMPUTE_4BL_CD
Post 38 - SIG_VERIFY_4BL_CD
Post 39 - SHA_VERIFY_4BL_CD
Post 3A - BRANCH
Post 3B - PCI_INIT
Post 3C
Post 3D
Post 3E
Post 3F
Post 40 - Entrypoint of CD reached
Post 41 - VERIFY_OFFSET
Post 42 - FETCH_HEADER
Post 43 - VERIFY_HEADER
Post 44 - FETCH_CONTENTS
Post 45 - HMACSHA_COMPUTE
Post 46 - RC4_INITIALIZE
Post 47 - RC4_DECRYPT
Post 48 - SHA_COMPUTE
Post 49 - SHA_VERIFY
Post 4A - LOAD_6BL_CF
Post 4B - LZX_EXPAND
Post 4C - SWEEP_CACHES
Post 4D - DECODE_FUSES
Post 4E - FETCH_OFFSET_6BL_CF
Post 4F - VERIFY_OFFSET_6BL_CF
Post 50 - LOAD_UPDATE_1
Post 51 - LOAD_UPDATE_2
Post 52 - BRANCH
Post 53 - DECRYT_VERIFY_HV_CERT
Post 54
Post 55
Post 56
Post 57
Post 58 - INIT_HYPERVISOR
Post 59 - INIT_SOC_MMIO
Post 5A - INIT_XEX_TRAINING
Post 5B - INIT_KEYRING
Post 5C - INIT_KEYS
Post 5D - INIT_SOC_INT
Post 5E - INIT_SOC_INT_COMPLETE
Post 5F
Post 60 - INIT_KERNEL
Post 61 - INIT_HAL_PHASE_0
Post 62 - INIT_PROCESS_OBJECTS
Post 63 - INIT_KERNEL_DEBUGGER
Post 64 - INIT_MEMORY_MANAGER
Post 65 - INIT_STACKS
Post 66 - INIT_OBJECT_SYSTEM
Post 67 - INIT_PHASE1_THREAD
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS
Post 69 - INIT_KEY_VAULT
Post 6A - INIT_HAL_PHASE_1
Post 6B - INIT_SFC_DRIVER
Post 6C - INIT_SECURITY
Post 6D - INIT_KEY_EX_VAULT
Post 6E - INIT_SETTINGS
Post 6F - INIT_POWER_MODE
Post 70 - INIT_VIDEO_DRIVER
Post 71 - INIT_AUDIO_DRIVER
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init
Post 73 - INIT_SATA_DRIVER
Post 74 - INIT_SHADOWBOOT
Post 75 - INIT_DUMP_SYSTEM
Post 76 - INIT_SYSTEM_ROOT
Post 77 - INIT_OTHER_DRIVERS
Post 78 - INIT_STFS_DRIVER
Post 79 - LOAD_XAM
Post 7A
Post 7B
Post 7C
Post 7D
Post 7E
Post 7F
Done!

Version: 10
Press Escape to exit
Waiting for POST to change
Post 7F
Done!


===================================================
Monday, July 13, 2015 1:57:30 AM

J-Runner v0.3 Beta (7) Started


WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button


Checking Files
Finished Checking Files
Version: 10
Press Escape to exit
Waiting for POST to change
Post 7F

===================================================
Monday, July 13, 2015 2:03:12 AM

J-Runner v0.3 Beta (7) Started


WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button


Checking Files
Finished Checking Files
Version: 10
Press Escape to exit
Waiting for POST to change
Post 7F
Done!

Version: 10
Press Escape to exit
Waiting for POST to change
Post 7F
Done!

Version: 10
Press Escape to exit
Waiting for POST to change
Post 7F

===================================================

What could be causing this issue????? :/ I know there is no issue with the soldering because i've triple checked every single point with a multimeter for faults. Could there be something wrong with the Xell image or something? ?? Thank you in advance