MrKronic 7 Posted July 12, 2015 Hello again. So this time, I've been having an issue with another phat Jasper console that has been installed with a CR4 XL board. The NAND has been flashed with Xell, but so far I've had no luck in actually booting into it. The console starts up normally (no RRODs whatsoever and the power light turns green etc.), but I don't get any display regardless of which display port I use (I've tried the composite and the HDMI).So far, I've done a POST monitor of the boot-up which seems to indicates that everything seem to be initializing properly and no POST faults, however the code cascade seems to be a bit too long in comparison to the normal POST codes (including the expected Xell code) in Martin C's POST calculator. Also, strangely enough, after the console is switched on the first time, the POST monitor always initializes with a 7F code and stays stuck in it regardless of whether the xbox is switched on or not. This is reset every time I switch off the power box and repeat the process. =================================================== Monday, July 13, 2015 1:55:18 AM J-Runner v0.3 Beta (7) Started WARNING! - Your selected working directory already contains files! You can view these files by using 'Show Working Folder' Button Checking Files Finished Checking Files Checking Console.. Version: 10 Flash Config: 0x00000000 Can not Continue Can not continue Checking Console.. Version: 10 Flash Config: 0x00AA3020 00AA3020 Jasper 512MB CB Version: 6723 Version: 10 Press Escape to exit Waiting for POST to change Post 01 Post 03 Post 04 Post 05 Post 06 Post 07 Post 08 Post 09 Post 0A Post 0B Post 0C Post 0D Post 0E Post 0F Post 10 - Payload/1BL started Post 11 - FSB_CONFIG_PHY_CONTROL Post 12 - FSB_CONFIG_RX_STATE Post 13 - FSB_CONFIG_TX_STATE Post 14 - FSB_CONFIG_TX_CREDITS Post 15 - FETCH_OFFSET Post 16 - FETCH_HEADER Post 17 - VERIFY_HEADER Post 18 - FETCH_CONTENTS Post 19 - HMACSHA_COMPUTE Post 1A - RC4_INITIALIZE Post 1B - RC4_DECRYPT Post 1C - SHA_COMPUTE Post 1D - SIG_VERIFY Post 1E - BRANCH Post 1F Post 20 - CB entry point reached Post 21 - INIT_SECOTP Post 22 - INIT_SECENG Post 23 - INIT_SYSRAM Post 24 - VERIFY_OFFSET_3BL_CC Post 25 - LOCATE_3BL_CC Post 26 - FETCH_HEADER_3BL_CC Post 27 - VERIFY_HEADER_3BL_CC Post 28 - FETCH_CONTENTS_3BL_CC Post 29 - HMACSHA_COMPUTE_3BL_CC Post 2A - RC4_INITIALIZE_3BL_CC Post 2B - RC4_DECRYPT_3BL_CC Post 2C - SHA_COMPUTE_3BL_CC Post 2D - SIG_VERIFY_3BL_CC Post 2E - HWINIT Post 2F - RELOCATE Post 30 - VERIFY_OFFSET_4BL_CD Post 31 - FETCH_HEADER_4BL_CD Post 32 - VERIFY_HEADER_4BL_CD Post 33 - FETCH_CONTENTS_4BL_CD Post 34 - HMACSHA_COMPUTE_4BL_CD Post 35 - RC4_INITIALIZE_4BL_CD Post 36 - RC4_DECRYPT_4BL_CD Post 37 - SHA_COMPUTE_4BL_CD Post 38 - SIG_VERIFY_4BL_CD Post 39 - SHA_VERIFY_4BL_CD Post 3A - BRANCH Post 3B - PCI_INIT Post 3C Post 3D Post 3E Post 3F Post 40 - Entrypoint of CD reached Post 41 - VERIFY_OFFSET Post 42 - FETCH_HEADER Post 43 - VERIFY_HEADER Post 44 - FETCH_CONTENTS Post 45 - HMACSHA_COMPUTE Post 46 - RC4_INITIALIZE Post 47 - RC4_DECRYPT Post 48 - SHA_COMPUTE Post 49 - SHA_VERIFY Post 4A - LOAD_6BL_CF Post 4B - LZX_EXPAND Post 4C - SWEEP_CACHES Post 4D - DECODE_FUSES Post 4E - FETCH_OFFSET_6BL_CF Post 4F - VERIFY_OFFSET_6BL_CF Post 50 - LOAD_UPDATE_1 Post 51 - LOAD_UPDATE_2 Post 52 - BRANCH Post 53 - DECRYT_VERIFY_HV_CERT Post 54 Post 55 Post 56 Post 57 Post 58 - INIT_HYPERVISOR Post 59 - INIT_SOC_MMIO Post 5A - INIT_XEX_TRAINING Post 5B - INIT_KEYRING Post 5C - INIT_KEYS Post 5D - INIT_SOC_INT Post 5E - INIT_SOC_INT_COMPLETE Post 5F Post 60 - INIT_KERNEL Post 61 - INIT_HAL_PHASE_0 Post 62 - INIT_PROCESS_OBJECTS Post 63 - INIT_KERNEL_DEBUGGER Post 64 - INIT_MEMORY_MANAGER Post 65 - INIT_STACKS Post 66 - INIT_OBJECT_SYSTEM Post 67 - INIT_PHASE1_THREAD Post 68 - Started phase 1 Initialization + INIT_PROCESSORS Post 69 - INIT_KEY_VAULT Post 6A - INIT_HAL_PHASE_1 Post 6B - INIT_SFC_DRIVER Post 6C - INIT_SECURITY Post 6D - INIT_KEY_EX_VAULT Post 6E - INIT_SETTINGS Post 6F - INIT_POWER_MODE Post 70 - INIT_VIDEO_DRIVER Post 71 - INIT_AUDIO_DRIVER Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init Post 73 - INIT_SATA_DRIVER Post 74 - INIT_SHADOWBOOT Post 75 - INIT_DUMP_SYSTEM Post 76 - INIT_SYSTEM_ROOT Post 77 - INIT_OTHER_DRIVERS Post 78 - INIT_STFS_DRIVER Post 79 - LOAD_XAM Post 7A Post 7B Post 7C Post 7D Post 7E Post 7F Done! Version: 10 Press Escape to exit Waiting for POST to change Post 7F Done! =================================================== Monday, July 13, 2015 1:57:30 AM J-Runner v0.3 Beta (7) Started WARNING! - Your selected working directory already contains files! You can view these files by using 'Show Working Folder' Button Checking Files Finished Checking Files Version: 10 Press Escape to exit Waiting for POST to change Post 7F =================================================== Monday, July 13, 2015 2:03:12 AM J-Runner v0.3 Beta (7) Started WARNING! - Your selected working directory already contains files! You can view these files by using 'Show Working Folder' Button Checking Files Finished Checking Files Version: 10 Press Escape to exit Waiting for POST to change Post 7F Done! Version: 10 Press Escape to exit Waiting for POST to change Post 7F Done! Version: 10 Press Escape to exit Waiting for POST to change Post 7F =================================================== What could be causing this issue????? :/ I know there is no issue with the soldering because i've triple checked every single point with a multimeter for faults. Could there be something wrong with the Xell image or something? ?? Thank you in advance 1 Quote Share this post Link to post Share on other sites