Search the Community

I have 6 xbox 360's 4 Xenon's, 1 Zephyr, and 1 Trinity. I have tried to get the correct information to S-RGH any one of them. There are so many conflicting tutorials, stuff gets outdated, people have refereed me to links that have been non-existent for years, I was told the best one to mod is the trinity. So where can I find a complete guide to mod my slim Trinity thats current and up to date with out broken links ect. I have in my possession two cool runner REV C chips, two Matrix SPI NAND reader/writers and 2 ACE360 V3's. I got plenty of all types of wire, good solder, 3 soldering irons, hot glue gun, heat shrink in different color and sizes, several different windows laptop and desktop computers, a USB 40x digital microscope, flux, heat gun, temp controlled convection oven, tons of extra capacitors, resistors, MOSFET's, transistors, diode's micro switchs, LED's ect. What I do not have is a diagram that shows me where to hook up the MATRIX SPI NAND V1 to what points on my Trinity, then should I use the Coolrunner V3 or the ACE360 V3? ANd where do I solder that in at? Can some one steer me to the info im looking for, I all ready tore out my hair, smashed one xbox 360 (zephyr) got drunk several times, fought with idiots sending me broken links after complaining getting broken links sent to me, wrong info, and a whole bunch of things making me frustrated. It can be done, i can do it, but I need a little help here.

I have a Corona V1 RGH with a CR4 XL that will not boot an rgh image. It was booting yesterday, but I cannot get it to boot today. The red light on the CR comes on and the green light flashes every five seconds. I flashed my NAND backup and it boots fine. Any help would be greatly appreciated. Thanks.

I have searched the internet to no avail. I hope somebody can help me here. I have done my fare share of RGH 1.2, and RGH 2, but never had this issue. My Coolrunner keeps glitching at the same rate no matter what timing file I put in it. I can't get xell to boot. I tried pulling the wires one at a time, if I remove RST, PLL, or POST it quits trying to glitch. The CLK doesn't seem to make a difference. If I re-write my original nand, it boots fine so hardware is still good. I forgot to mention, I'm doing RGH 1.2 on a Jasper 256mb. If anyone could help me it would be greatly appreciated.

Originally Posted by Ubergeek on Team-Xecuter.com: WARNING*********WARNING*********WARNING*********WA RNING********* PLEASE BE AWARE THAT THE XC264A BASED RGH HACK FOR THE CORONA IS NOT VERY RELIABLE AND DOES NOT GLITCH VERY FAST AT ALL. THE HACK IS MADE AVAILABLE SO YOU CAN HAVE A PLAY WITH THIS YOURSELF AND SEE WHAT RESULTS YOU CAN ACHIEVE. THIS IS WHY WE DESIGNED THE COOLRUNNER 3, IT HAS BEEN FINE TUNED USING A MUCH MORE ADVANCED DESIGN AND GLITCHES VERY RELIABLY AND VERY FAST. WE DO NOT OFFER ANY GUARANTEES OR SUPPORT WITH THE XC264A CORONA HACK. WARNING*********WARNING*********WARNING*********WA RNING********* To get this working on CoolRunner Rev A B or C you simply have to add a 48.000MHz crystal. If you have Rev A or Rev B remember to remove C15. It's a bit cheap and cheerful and the hack isn't that good with the limitations of the older gen XC264A hardware but here it is anyway. The crystal has to be good quality - not some cheap crappy one as it will not work. These work very well: http://ie.farnell.com/jsp/search/pro...sp?SKU=1640968 48.000MHz crystal wiring to the CoolRunner: PIN 1,4 to 3v3 PIN 2 to GND PIN 3 to B We have included 6 files with different timings tx_corona_0_2.xsvf tx_corona_0_3.xsvf tx_corona_1_2.xsvf tx_corona_1_3.xsvf tx_corona_2_2.xsvf tx_corona_2_3.xsvf The most important point is the CPU_RST - this will make the difference between a 30 second glitch and a 30 minute glitch. You may want to try using the CPU RESET CLEANER addon that we released - it works very well with RGH1 and RGH2. We also recommend you try the different wire layouts as per the original CoolRunner instructions. CoolRunner 3 is in production right now - you will get to see how Slim glitching should be done Thanks to GliGli & Tiros for the original RGH exploit. - Team Xecuter On a side note.... These are the crappy glitch times you should expect (measured with the CoolRunner 3 RATER) These are cycles - not seconds (1 cycle = 5 seconds). In our opinion it just isn't worth paying for - so we encourage you not to buy a CoolRunner REV C or any other XC642A based glitcher just to do Corona - you will probably be dissapointed. 11, 51, 14, 5, 5, 26, 19, 1, 1, 13, 18, 3, 1, 3, 4, 6, 8, 5, 5, 9, 3, 2, 7, 22, 14, 4, 6, 5, 1, 2, 16, 2, 5, 17, 8, 10, 8, 8, 9, 4, 13, 2, 9, 4, 19, 2, 8, 2, 10, 11, 1, 14, 1, 2, 10, 4, 3, 3, 3, 1, 3, 20, 4, 4, 6, 15, 7, 3, 18, 3, 6, 6, 1, 2, 3, 11, 2, 37, 3, 13, 1, 10, 9, 4, 10, 6, 3, 14, 2, 4, 4, 4, 6, 4, 2, 1, 6, 1, 9, 3, 4, 2, 8, 2, 5, 15, 3, 3, 1, 2, 6, 7, 6, 21, 15, 27, 11, 9, 4, 10, 2, 5, 11, 3, 6, 14, 26, 8, 2, 5, 4, 3, 11, 3, 15, 4, 10, 13, 14, 22, 22, 9, 6, 22, 19, 1, 5, 10, 5, 1, 7, 2, 16, 9, 1, 11, 2, 7, 24, 3, 8, 12, 8, 7, 12, 13, 4, 7, 3, 1, 17, 9, 2, 5, 3, 2, 5, 1, 16, 4, 9, 9, 3, 1, 1, 15, 18, 3, 7, 3, 49, 18, 9, 6, 4, 1, 2, 11, 1, 3, 1, 5, 14, 12, 16, 11, 1, 8, 11, 1, 47, 8, 1, 19, 2, 18, 9, 6, 7, 15, 12, 13, 6, 16, 5, 3, 11, 3, 12, 2, 5, 2, 11, 4, 1, 18, 8, 13, 8, 10, 8, 1, 1, 13, 10, 5, 38, 10, 20, 3, 8, 4, 7, 4, 17, 3, 6, 1, 8, 13, 2, 3, 2, 10, 1, 1, 30, 17, 7, 14, 24, 10, 1, 16, 11, 16, 5, 6, 6, 11, 6, 1, 15, 1, 3, 5, 25, 10, 7, 5, 13, 12, 6, 8, 5, 7, 1, 46, 2, 17, 14, 2, 2, 6, 3, 3, 2, 5, 23, 3, 1, 8, 23, 15, 5, 1, 3, 3, 3, 1, 2, 5, 10, 9, 9, 20, 7, 22, 1, Xecuter_DIY_Corona16_Coolrunner_Upgrade.zip