steveo1978

Make sure 360 IP address has not changed and that the device name is correct

Rocknrolla arent you the one I helped on IRC that just needed to set the USBMU0 option?

Did you use ISO2GOD on the ISO for disc one? If you did thats your issue and you should use exiso GUI to extract the files from the ISO.

Extracting Disc1 1st) Click the "Browse" button and navigate to the place you would like the iso to be extracted to. I have noticed that sometimes this path does not get set correctly and files end up getting extracted somewhere else, so set the path then exit and re-open Exiso GUI. 2nd) Click the "Add an ISO" button and just load the ISO for GTA Disc1. 3rd) Click the "Go" button and let it run. The extraction time will vary depending on the amount of RAM in your PC and it best to not do anything until Exiso GUI has finished. Once its finished you will be notified by a pop-up just hit "OK" on that box and exit out of ExISO GUI. Using 360 Content Manager to install the needed files 1st) Click the settings button in Content Manager so that the proper settings can be applied. ***For All of the following steps you will need FreeStyleDash (FSD) running with FTP enabled.*** 2nd) In Settings click the "FTP" tab 3rd) Set the IP address to match the IP address that you are giving in FSD. 4th) To verify that your IP is correct and able to connect to FSD click the "Test" button. If the test fails make sure Content Manager is not blocked by your PCs firewall and that FTP is enabled in FSD. 5th) If you are install this to an internal HDD then you can skip this and move on to the 6th step. If you are using a USB Memory Unit type "USBMU0" (zero not an o at the end) with out quotes into the box. 6th) Click "Save" button 7th) Navigate to the folder that contains the extracted ISO files you got from running ExISO GUI earlier 8th) Right Click the folder 9th) Select "Load Files From Subfolders" 10th) After the folder is scanned you should get 4 files listed under "Game Add-On" put a check mark beside the files like in the screenshot. 11th) Click the button to FTP the selected files to the 360. 12th) On this screen just click the "Upload" button. Its 7.69GB of files so it will take some time to FTP all the files to the 360. Once its finished you can exit out of 360 Content Manager. This is all that needed from Disc1 so there is no need to copy anything other then the 4 files you just FTPed to the 360. For Disc2 just treat that as a single disc game from here. There is no need to try and set it up as a multidisc game. There have been reports of GTA 5 having issues if ran from the same device as the installed content (Disc1 Content) so my suggestion is if you installed the disc1 content to a internal HDD then try to run disc2 content from an external HDD. Apps: ExISO GUI and 360 Content Manager These apps my need to be ran in Administrator Mode http://www.mediafire.com/?fk55d8zvg87aol1

My condolences go out to you. If you will PM me your shipping info I will get the Glitch360Key Ultra shipped out as soon as possible.

As a thank you to TeamFSD, 360crunch.net would also be giving the winner of this contest a Glitch360Key Ultra to go along with the Glitch360 SPI that they are currently offering as a prize. So that people that have either already entered or at least thinking about entering, I am posting links to the reviews I have done on both devices. Review: Glitch360Key Ultra Review: Glitch360Spi 3.0 rev b Once again thank you TeamFSD for all your hardwork and best of luck to all of those that enter.

Posted on Saturday 05/Jan/2013 Link ---------> [click=http://www.mediafire.com/?vs88v4bev377d92]Rogero_CEX4.30_V2.04.PUP[/click] MD5: 9f148cb1e265810e9f962ffd4119d0fc Size: 192 MB (201,591,424 bytes) For all the users that are having the Singstar Icon on XMB, please know that this is a pure Original FW 4.30/4.31 feature and it seems it is only showing for Europe users when they connect the PS3 to the internet. Here's two links to the SingStar problem with OFW4.30 : ---> Singstar Icon appeared after online update to FW 4.30 ---> Singstar Icon appeared after online update to FW 4.30 [click=http://www.sendspace.com/file/klv9jz]installPKG [singStar Replacement].pkg (254.08KB)[/click] quoted from Dean: This CFW was tested on most PS3 Models by different testers and no problems were encountered. But as any CFW release you must install it with caution and by following proper instructions, No one will be held responsible for any damage caused. * This CFW can be installed fine from XMB Update over any OFW3.55/CFW3.55/CFW4.21/CFW4.30. * For details about Downgrading back to CFW/OFW3.55 Please read the Downgrade Guide below Rogero CFW4.30 v2.04 Change-log * Added the new patches that allowed the return of the Original "*Install Package Files", Credits to Szalay and "hidden Man". * Updated Dean's "*Install Package files" on [app_home] to the latest version that doesn't requires a PS3 Restart anymore. * All the previous features of version 2.03 are all preserved. Rogero CFW4.30 v2.03 Details * Rebuilt from scratch using OFW4.30 files only (no DEX/SEX files) with official XMB and full features working as in OFW4.30 * All known problems like XMB icons sorting and Demo Mode issues from previous versions are now gone with the use of the official XMB. * New Improved "Install Package Files" Application added to XMB instead of using the traditional DEX Icon, to have a 100% original XMB. * Once the PS3 is booted, select the [app_home/PS3_GAME] Icon and It will change automatically to [* Install Package Files] * If you load a Game from multiMAN it will still be redirected and shown under the same [app_home/PS3_GAME] Icon * After loading a Game, you can restart the PS3 again to have [* Install Package Files] back on XMB * You can also Install the new stand-alone XMB application from Deank --> [* Install Package Files] to have it showing permanently on XMB. - [* Install Package Files] function supports: --- up to 256 pkg files --- split pkg files --- sorting --- queued PKG indication (in red) --- multipart (split) PKG indication (in yellow) --- copy/transfer progress --- Scanned locations: /dev_usb*** /dev_hdd0 /dev_bdvd in /PKG /packages and root folders --- Split files format: .0 - .63 / .66600 - .66663 / .001 - .064 * CFW Structure fixed to match the OFW 4.xx Structure: --- No more corrupted data error messages while Installing from XMB or Recovery Menu. --- The CFW can be installed fine from XMB Update over any OFW3.55/CFW3.55/CFW4.21/CFW4.30. --- HDD can be swapped/changed and the CFW4.30 v2.03 will re-install without any problem. * Patched LV1 to disable LV2 Protection. * Patched LV1 to add peek/poke support to replace hvc 182/183 (multiMAN Direct Disc Access is now working fine with CFW4.30 v2.03) * Patched LV1 to disable SYSTEM MANAGER INTEGRITY CHECK (to prevent Bricking on non-dehashed downgraded consoles) * Patched LV1 Core OS Hash Check (to prevent Bricking on non-dehashed downgraded consoles) * The CFW can be used directly for Downgrading with Hardware flashers /Flashing from FSM/Exiting from FSM, all works fine. * The CFW have both noBD/noBT patches to allow installation on consoles with broken BluRay Drive or Bluetooth board. * Patched LV2 to add peek/poke support. (for both LV1 and LV2) * Patched VSH to enable ReActPSN compatibility (Allow Unsigned act.dat and *.rif files, Disable Unlinking/Deleting of act.dat) * Spoofed the system version to latest OFW version 4.31. * PSN/SEN access is available as long as the current "passphrase" still the same. * Loading games from App_home Icon is now fixed. * It can run games signed with Keys up to version 4.30 without any Eboot/Sprx patching needed * Games can be loaded from Disc Icon (with Original game in BD) and from app_home (Disc-less, but not all games). * Current 3.55 homebrew applications can't be loaded on this CFW, applications must be re-signed properly for FW4.21/4.30 ATTENTION: 1- This CFW does have LV1 checks disabled and can be installed on Downgraded PS3 consoles even if not dehashed after downgrade. Just in case anyone still need to dehash, here's the link Link ----> Dehashing Tutorial 2- Always make a NOR/Nand dump using multiMAN before installing any CFW to have a recovery backup in case of any bricks. Having a valid NOR/Nand dump is an essential step before upgrading, because you will always have a chance to recover when you have a valid dump. ** A Hardware Flasher alone without a valid dump may not fix your bricked PS3 ** 3- The QA flag is better to be always Enabled on your PS3 for safer upgrading/downgrading operations. Link ----> toggle_qa.pkg 4- Please Check the MD5 of the downloaded PUP file before installing any CFW to avoid possible bricks. 5- DO NOT HAVE DISC IN PS3 WHEN UPDATING FIRMWARES..As the PS3 will take the UPDATE from the DISC First. 6- You need to be already on a 3.55OFW or 3.55CFW/4.21CFW/4.30CFW to install this. Installing from any OFW > 3.55 won't work. (Hardware Flasher needed) - Downgrading back to 3.55 is always possible using the following steps : - Download the Downgrader PUP ---> Downgrader PUP mirror ---> Downgrader PUP ...Size 176MB (184,595,263 bytes) MD5: 49d80e07fc1f5ca1b0840e02e94635db - Rename the downloaded file to "PS3UPDAT.PUP" and put it on your USB in: "USBPS3UPDATEPS3UPDAT.PUP" - While on Rogero CFW4.30, go to System Update from XMB and install the Downgrader PUP. - After the Downgrader PUP installs you'll be on a hybrid CFW3.55 that will still shows the spoofed ver4.21 from system settings. - In case you didn't have it Set Before, Enable QA flag by following these steps: 1- Download the Rebug QA_Toggle package from here ---> toggle_qa.pkg 2- Put the "toggle_qa.pkg" on USB and Install it on the PS3. 3- Run the "Rebug Toggle QA" from XMB, the screen will go Black and you will see HDD Led activity then if all went fine you will hear 2 or 3 Beeps and the PS3 will Restart back to XMB. 4- If you want to make sure QA flag was set, go to "Network Settings" then apply the following key combo (all at the same time): [highlight=#ffff00]L1 + L2 + L3 (press left stick) + R1 + R2 + dpad_down[/highlight] You should see Edy Viewer, Debug Settings, and Install Package Files if done correctly. - Now put "Rogero CEX-3.55 CFW V3.7" on your USB in: "USBPS3UPDATEPS3UPDAT.PUP" ---> Rogero CEX-3.55 CFW V3.7.PUP - Start the PS3 and install "Rogero CEX-3.55 CFW V3.7" using the System Update from XMB. - Once you're back on Rogero CFW3.55 v3.7 you can now install any CFW 3.55/4.21/4.30 using the System Update from XMB ( or Recovery Menu if XMB Update didn't work ). Credits to : *- Szalay and "hidden Man" for the new patches that allowed the return of the original [*Install Package Files] Function. *- Deank for his continuous efforts on Multiman, the new "Install Package Files" Function and all his assistance during the build process. *- Evilnat [Nathan_r32_69] for all his contribution with the code, awesome tools, and the Sleepless nights working/testing together. *- Abkarino [DVD4Arab] for all his research, coding, tools, and help (Good job my friend) *- The Anonymous source of valuable information ( you know who you are, much Respect ) *- Cyberskunk/Rebug Team for the hints about fixing the UPL package and the Build number, Thank you. *- All Tortuga-Cove Staff from Admins and Moderators (Thank you Windrider for all the support provided) *- PS3DevWiki for the valuable and always up-to-date source of information. Source : http://tortuga-cove....hp?f=127&t=4336

That looks pretty cool