update to 16747 , works with RGH ?

[s8n 13]

hi members and Swizzy ,  im currently on 16537 and thinking of updating the dash to 16747 via USB

 

will i be able to RGH the console ?

 

i believe i can but want to be sure

 

btw my Coolrunner 4's have been shipped and should arrive Monday

[Anonymous 95]

So you have planned for modding your Console

Is this your first time for modding???

Do you knw what kind of mother board u hav???

Did u read proper tutorials??

Sent from my ST23i using Tapatalk

[s8n 13]

hi Anonymous ,  ive been researching and planning for about 6 months now it is my first time modding a 360.  The motherboard is a Jasper ,  i have read 2 different Tutorials and watched Youtube videos from Keil423 and thedopesoner930 ive also asked questions over at TX forums and here.

 

ive written my own guide/tutorial after researching for my own use ,  i will use it when the Coolrunners arrive i want to get Swizzy to check the guide/tutorial i wrote at some point

[Swizzy 2083]

ive written my own guide/tutorial after researching for my own use ,  i will use it when the Coolrunners arrive i want to get Swizzy to check the guide/tutorial i wrote at some point

Where is it at?

Jaspers can be hacked with any kernel version now a days, the stability of the hack depends on what version of CB you're on (if you can use JTAG it's always going to be stable, rgh 1 is fairly easy to get stable) if you're on a unsupported CB for these hacks, you should probably go for R-JTAG (or CR4) as it's fairly easy to get stable aswell

[s8n 13]

hi Swizzy great tips as usual ,  below is my guide/tutorial a very small portion is copied and pasted from the Coolrunner manual.

 

 

1.  solder QSB's to XBOX motherboard ,  after that plug in power and power on the 360.

if it boots fine the soldering is good and theres no bridges or other problems etc.............

 

 

2.  turn off and disconnect power from 360 ,  then connect J-Runner

IMPORTANT plug in power but dont turn the 360 on

fire up J-Runner software ,  do 4 Reads of the NAND

make sure NAND Type is set for the motherboard

make sure theres no errors in the log...................

after 4 Reads done compare NANDs so they match...........

 

compare 1 and 2

then 3 and 4

then 1 and 3

 

if they all match zip up the NAND files ,  they will most likey be in the ' output ' folder


FLASHCONFIG - MOTHERBOARD TYPE
01198010 - Xenon, Zephyr, Opus, Falcon
00023010 - Jasper 16mb, Trinity 16mb
008A3020 - Jasper 256mb
00AA3020 - Jasper 512mb

 

if motherboard is not 00023010 - Jasper 16mb, Trinity 16mb ,  contact Swizzy

 

 

3.  now write the ECC ,  make sure there are no errors in the log

once written wait 30 seconds then disconnect power and wait 30 more seconds.

remove J-Runner cables from QSB's...............

now solder wires from the Coolrunner 4 to the QSB's and motherboard.
 

 

4.  try and boot XELL ,  plug in power and network cable

turn on 360 from the front of the console

once XELL has fully loaded get the IP address of the 360 and enter it into J-Runner software.

hit ' Get CPU Key '

J-Runner should show KV info when it retrieves the CPU Key
 

 

5.  J-Runner should reload your nanddump1.bin into source box again in preparation of key validation and image creation


if it doesnt automatically reload it ' browse ' and manually load nanddump1.bin into the source box


Now you should have all the info in KV tab in the right hand box and you will get a CPU Key verified message in the log


take a snapshot of the screen with Hypersnap of ............

NAND info
KV info
Bad Blocks


At this point you now have all the info you need to create a Freeboot image.


Turn off XBOX and disconnect power ,  wait 30 seconds
 

6.  Reconnect J-Runner Programmer and connect power but dont turn on the XBOX

 

in J-Runner software goto Dashlaunch tab and enable ' use Dashlaunch '


enable ' include launch.ini '


use the configurator to my liking in J-Runner

create launch.ini

save the settings


Now click Create XeBuild Image button

make sure theres no errors in the log

 

 

7.  Now flash this image to your NAND

press Write NAND

make sure theres no errors...................

 

Once finished flashing wait 30 seconds


unplug power and wait for 30 more seconds


remove J-Runner Programmer


then plug in USB hard drive with FreeStyleDash on it


Then replug power to 360 and turn on