Leaderboard

Up for sale I have one piece of TX DemoN SLIM, removed from a console at the customer's request. DemoN was working until the last day when it was removed from console so it is in well working condition. The picture below is made with removed DemoN, connected just through USB cable. DemoN comes with all the parts same as you would receive it from the shop except the wires (some are missing). It became rare lately as it is hard to find one for sell. It includes retail box, a card with warning notice, DemoN itself, daughter board, CR extension board, Corona 16MB V1/V3 upgrade QSB, unused ribbon cables (factory sealed) and unused genuine sticker. I'm asking $50 $40 +shipping. Currency can also be converted either to EUR or GBP. I can ship worldwide. Payment via PP gift or Amazon Gift Card, both possible.

This is NOT for updating your JTAG/RGH dashboard/kernel, this is for installing Avatar/Kinect data ONLY. To change the dashboard/kernel version of your JTAG/RGH console, you build a new image with J-Runner or similar. Before you proceed, ensure you have an internal hard drive connected with enough space for the update (I think somewhere around 128MB is required). Also, ensure that you have DashLaunch installed and configured. So, you have a JTAG or RGH system, but no Avatars or Kinect? This small tutorial will help you install them (ensure your Kinect hardware is connected before you begin or you will be prompted to update again once you connect it!). Step 1 Download the USB system update from here (remember to check that the system update you download matches your JTAG/RGH kernel version - go to System Settings>Console Settings>System Info and read where it says Dashboard: 2.0.XXXXX.0, where X = your current dashboard/kernel version). Step 2 Extract the $systemupdate folder from the archive with 7-Zip or similar and rename it to $$ystemUpdate. Step 3 Transfer the $$ystemUpdate folder (the one you renamed in Step 2) to the root of a FAT32-formatted USB stick (I recommend 512MB+). Step 4 Connect your USB stick to your console, power it on and accept the update when prompted. There are different messages shown based on what the system update is going to apply. If you see this: Do NOT accept the update because this is telling you that the system is going to attempt a complete update which alters bootloaders and it will also burn eFUSEs. If you see this: It is fine to proceed with the update. This is the system telling you that additional components are missing. The console will reboot once the update has installed successfully and you should now see Avatars and have Kinect installed (don't forget to configure it!). If the console doesn't do anything, ensure that: The update folder is named correctly.The system update you are applying matches the JTAG/RGH dashboard/kernel version your console is currently running (see Step 1).You inserted the USB stick before booting the console (FSD can block the system update).If, after all this is attempted, the console still won't update, go into FSD and then into the File Manager, look for a SysExt: folder and delete what you can (don't forget to enable File Manager Advanced Mode in General Settings first). Reboot the console and you'll be told that there are corrupted files - reboot the console to resolve this. Do this with the USB stick connected and your console should prompt you to accept the update. I find that if I boot the console to NXE/Metro (hold RB after powering the console on) and THEN insert the USB stick, the update prompt shows up.

Yeah, didnt see that until after I posted, as both posts were within 30 seconds of each other. lol.

very cool looking, thanks to everyone for their input and support, esp the devoleprs etc

Thanks Team Phoenix! I'm in quite a strange 'gaming' period of my life at the moment where I enjoy 'tinkering' with gaming platforms, rather than actually playing on them! With the excellent Aurora dash and the great support I received here, the 360 is my current fav tinker toy.

Hey! much apperciated your great work Team Phoenix...Aurora is great!

Thank you phoenix team and RMS for all the hard works!!

i tried in battlrfield4, pes15, hitman absolution with the latest TU. Brobably i've run wrong games. thank you

Ok I got my ports to pass but now I'm getting. JQ360.exe Authentication status: Auth klbarnes1: Fail Any idea on how to fix this?